0 votes
2 answers
145 views
It seems that the "Start 1st Chapter on a New Page" option is not working in PTXPrint 2.7.6. If I select "All Chapters" ... I'm missing? Chapter 1 is marked with \c 1 in Paratext.
0 votes
2 answers
129 views
PTXprint 2.6.11 Is it possible to use Book \id for the PDF bookmarks?
0 votes
1 answer
77 views
PTXprint 2.6.11 This option in Advanced/Page Layout and Spacing seems not work correctly.
0 votes
1 answer
56 views
We were teaching a Paratext class this past week, and were teaching them how to use PTXprint. The translators in these ... it is deactivated). Thanks for considering it... Jeff
0 votes
1 answer
59 views
We are working on a Bible module and upgraded to v 2.5.6 to get footnotes to appear in the PDF. Footnotes ... same problem - section headings do not display although footnotes do.)
0 votes
2 answers
73 views
When I try to run ptxprint on a specific chapter in my project (Luke 2), a strange and garbled PDF comes out. The ... official address) I will be happy to share the SFM file.
0 votes
2 answers
70 views
Hello everyone, I hope you are doing well. I am working on the layout of a book and have added a decoration at the ... . Thank you in advance for your help! Thanks for your help
0 votes
2 answers
85 views
Hi all, I'm working with a project that previously marked all footnote callers manually. Now, we have started ... , so I could just be missing something. Thanks, Aaron
0 votes
1 answer
87 views
The email the PTXPrint team sent out a month ago with information about Pretore in the Netherlands was pretty interesting. ... to our attention. It seems like a great possibility.
0 votes
1 answer
58 views
I have lines like this in a custom.vrs file: *REV 21:6,a,b I have USFM marking like this in Paratext: \v 6a ... 'm missing? I'd rather not print more than required. Thanks, Paul
0 votes
1 answer
70 views
We are typesetting a diglot project using PTXPrint, and the primary project has book introductions but the secondary ... full-width mode and back again? Or other suggestions?
0 votes
1 answer
78 views
It seems that if there is any \esb...\esbe material in the biblical text that a \ref field in a Module is trying ... error message (for a Module specifying verse 1 as the start).
0 votes
1 answer
73 views
Similar to the other diglot question from 2+ years ago, I have found a surprising (to me) behaviour trying to use ... documentation yet, so am happy to be pointed towards that.
0 votes
1 answer
40 views
Thank you very much. I have the attribution where we want it now (better there for certain "French" purposes). Now I ... I need to adjust? Here is a photo below. Thanks, Crockett
0 votes
2 answers
101 views
How do I add a short attribution phrase on the bottom right of the front cover image? I want it to say Designed by Freepik. Here is the image for reference: Thanks, Crockett
0 votes
2 answers
81 views
Hello, There should be plenty of room for the colophon further below to go on the last page after Psalm 150 and ... become a clickable url (if this were online)? Thanks, Crockett
+1 vote
1 answer
86 views
In a Right-to-Left Arabic script PTXprint PDF output of Psalms, I am getting too much space between things like the \ ... headings and titles? Here is an image of the issue: Thanks
0 votes
2 answers
107 views
I'm trying to match the layout of these two booklets. The texts and layout are the same except that the correct version ... But I can't seem to get back to this particular layout.
0 votes
1 answer
71 views
Hello, how are you? I'm stuck with PTXprint regarding a few chapters that end up with just one line at the bottom ... . If anyone has an idea, it would be greatly appreciated.
0 votes
2 answers
226 views
Greetings, I installed PTXprint on the SIL site as recommended, but when launching the software, it sends me an error message. ... as follows: What do I do to resolve this issue?
